Most self tapping screws in interiors never get called that on site. A karigar asks for a chipboard screw or a drywall screw, and both of them cut their own thread on the way in. The name only changes when there’s steel behind the board.
A gypsum false ceiling is boards screwed up into GI channels from below. Each screw goes through the gypsum and taps its own thread into the thin steel of the channel. The head has to stop flush with the paper.
A drywall screw has a bugle head. Its underside curves out like a trumpet. As it seats, it presses the paper down into the gypsum without tearing it. A chipboard screw’s countersunk head has straight sides, and the edge cuts the paper. Cut paper won’t hold the board to the channel.
SS Drywall comes in gauge 6 and gauge 8, which work out to 3.5mm and 4.5mm across, with lengths from 13mm to 75mm. Use the stainless one for bathroom and kitchen ceilings. It’s sturdier than the MS drywall screw too.
The same screw also fixes aluminium onto wood, which covers things like a profile shutter frame on a kitchen carcass or an aluminium track on a wooden partition.
The ceiling and the kitchen need different screws, but anyone fixing self tapping screws uses the same Phillips bit on both. In a modular kitchen, a wardrobe or a drawer, the screw goes into MDF or particleboard and has to cut a thread in board that splits easily.
That’s the job the SS Chipboard screw is made for. Its thread is deep and sharp, and it goes in without cracking the board. The range starts at (5) M3.0x12, which comes in packs of 1000, and goes up to (10) M5.0x100 in packs of 100. The number in brackets is the gauge. Hinges fixed into the side of a carcass take the same screw. CSK Phillips covers the rest of the hardware, like tower bolts, drawer channels and handles, in gauge 3 to 16.
Mild steel drywall screws in a bathroom ceiling rust, and the stain comes through the paint. A rusted screw up there can’t be swapped without opening the board, so go SS from the first fix.
Drive a self tapping screw into a steel box section without a pilot hole and the thread strips or the head snaps off. Drill a pilot hole first, or use a self drilling screw.
Fittings that sit on top of the wood need a different head altogether. Sofa legs, twin wheel castors and bed fittings with pneumatic pumps all have a steel plate, and a countersunk screw can’t clamp that plate down the way a pan head does. Pan Phillips holds in metal as well as wood. It also goes on bathroom fittings, and the SS version is the one to pick there.
| Where it goes | Screw | Size or capacity |
| Gypsum board onto GI channel | SS Drywall | Gauge 6 and 8, 13mm to 75mm |
| Aluminium section onto wood | SS Drywall | Gauge 6 and 8, 13mm to 75mm |
| MDF and particleboard furniture | SS Chipboard | M3.0 to M5.0, 12mm to 100mm |
| Castors, sofa legs, bed fittings | Pan Phillips | Gauge 3 to 16, 6.5mm to 150mm |
| Steel sub-frames and box sections | SDS | Drills metal 4mm to 4.5mm thick |
A self tapping screw needs a soft or thin start. Gypsum, board and a GI channel are all fine. Anything thicker, like a box section in a partition frame or a steel sub-frame behind wall panelling, needs a pilot hole first, which means two operations for every screw.
A self drilling screw has a small drill point on the tip. It makes its own hole and then its own thread, so there’s no pilot hole and no change of bit.
LP’s SDS is carbon steel and drills through metal 4mm to 4.5mm thick. A lot of the alternatives on the market stop at 1.5mm to 2mm. The coating is CR6+, at 6 microns or more, and the screw passes a 96-hour salt spray test. Check the head for the maker’s mark before you buy in bulk.
It’s still carbon steel under that coating, though. If the drawing says stainless, use a stainless screw and drill the pilot hole. There’s a fuller comparison of self tapping vs self drilling screws if you want the detail.
Before you order for a whole flat, list what each screw is going into, whether that’s gypsum, board, aluminium or steel, and order all of it together. Mark the spots that will see water, since those get SS. It helps to pick a self tapping screw manufacturer that also makes the self drilling ones, so the site isn’t waiting on a second supplier. LP Screw dispatches within 24 hours.
1. What are self tapping screws uses in a flat?
False ceilings, modular kitchens, wardrobes and aluminium sections fixed to wood. Any screw that cuts its own thread into gypsum, board or thin steel is doing a self tapping job.
2. Do self tapping screws need a pilot hole?
Not in gypsum, board or a GI channel. In thicker steel they do, and that’s where a self drilling screw saves the step by drilling its own hole.
3. Can I use self tapping screws in a bathroom?
Yes, as long as they’re stainless steel. Mild steel rusts in a wet room, and on a ceiling the SS drywall screw is also sturdier than the MS one.